Serial Number:Date of Purchase: Belt Drive Garage Door OpenerRaynor Garage Doors1101 E. River RoadDixon, Illinois 61021www.raynor.comWrite down the fo
10To avoid possible SERIOUS INJURY from afalling garage door opener,fasten it SECURELY tostructural supports of the garage.Concrete anchorsMUSTbe used
11To preventpossible OVERHEATING of the end panel or light socket:• Use ONLY A19 incandescent or compactfluorescent light bulbs.• DO NOT use incandesc
12Fiberglass,aluminum or lightweightsteel garage doors WILLREQUIRE reinforcement BEFOREinstallation of door bracket.Contact your door manufacturer fo
13IMPORTANT: The groove on the straight door arm MUST face away from the curved door arm.Straight Door ArmCurved DoorArm(Groove facing out)CORRECTINCO
141 Install the door controlInstall the Door ControlTo preventpossible SERIOUS INJURY or DEATHfrom electrocution:• Be sure power is NOT connected BEFO
15kInstall the Door Control1.5 Position the bottom hole of the doorcontrol over the screw and slidedown into place.1.6 Lift the push bar up and mark t
163 Attach the warning labelsInstall the Door Control3.1 Attach the entrapment warning label on the wall near the door control with tacks orstaples.3.
17IntroductionBe sure power is NOT connected to the garagedoor opener BEFORE installing the safetyreversing sensor.To preventSERIOUS INJURY or DEATH f
Install the Protector System®1 Install the Safety Reversing SensorsThe safety reversing sensors can be attached to the door track,the wall, or the flo
Install the Protector System®1 Install the Safety Reversing SensorsOPTION CFLOOR INSTALLATIONUse an extension bracket (notprovided) or wood black to r
2Safety Symbol and SignalWord ReviewThis garage door opener has been designed andtested to offer safe service provided it is installed,operated, maint
Install the Protector System®OPTION B PRE-WIRED INSTALLATION2.1B Cut the end of the safetyreversing sensor wire, makingsure there is enough wire torea
211 Connect PowerTo preventpossible SERIOUS INJURY orDEATHfrom electrocution or fire:• Be sure power is NOT connected to theopener, and disconnectpowe
222 Ensure the Safety Reversing Sensors are alignedThe door will not close if the sensors have not beeninstalled and aligned correctly.When the lightb
23Without a properly installed safety reversalsystem, persons (particularly small children)could be SERIOUSLY INJURED or KILLED by aclosing garage doo
241 Program theTravelWithout a properly installed safety reversal system,persons (particularlysmall children) could be SERIOUSLY INJURED or KILLED by
252 Test the Safety Reversal SystemWithout a properly installed safety reversal system,persons (particularly small children) could beSERIOUSLY INJURED
26To reduce the riskofFIRE or INJURY to persons:• DisconnectALL electric and battery powerBEFORE performing ANY service ormaintenance.• Use ONLY Rayno
27BATTERY STATUS LEDNOTE: The Battery Status LED is most visiblewith the garage door opener light off. Batterydoes not have to be fully charged to ope
28IMPORTANT SAFETYINSTRUCTIONSWARNING To reduce the risk of SEVERE INJURY or DEATH:1. READ AND FOLLOW ALL WARNINGS ANDINSTRUCTIONS.2. ALWAYS keep rem
29Your garage door opener is equipped with features to provide you with greater control over yourgarage door operation.TIMER-TO-CLOSEThe Timer-to-Clos
3ABCJNIOPDEFHGKLMOverview/Carton InventoryGARAGE DOOR OPENER ASSEMBLYA. tekcarb redaeH B. Pulley and bracketC. tekcarb rooD D. mra rood devruC E.
30USING THE DOOR CONTROLSYNCHRONIZETHEDOORCONTROLTo synchronize the door control to the garage door opener,pressthe push bar until the garage dooro
31MENU NAVIGATIONThe features on the door control can be programmed through a seriesofmenuson the screen and the navigation buttons.Refer to the descr
32Your garage door opener has been programmed at the factory to operate with your remote control. To programadditional remote controls refer to the in
333 Using a safety pin or paper clip,presstheprogram button until the LEDson the front ofthe remote control turn on.4 Press and release the Learn butt
34To prevent possible SERIOUS INJURY or DEATH from a falling garage door:• Ifpossible, use emergency release handle to disengage trolley ONLY when gar
35Diagnostic ChartYour garage door opener is programmed with self-diagnostic capabilities. The UP and DOWN arrows on the garage door opener flash the
36DIAGNOSTICCODEUPARROWFLASH(ES)DOWNARROWFLASH(ES)SYMPTOM CAUSE RESOLUTION3-3 3 3The garage door opener isidle and the battery LEDisconstantlyflashing
37Rail Assembly PartsDESCRIPTION PART NUMBER1 Belt - for 7 foot doorBelt - for 8 foot doorBelt - for 10 foot door41A5434-1141A5434-1341A5434-142 Belt
38Garage Door Opener Parts11124101953627843DESCRIPTION PART NUMBER1 Sprocket and Sprocket Cover withScrews41C589-22 End Panel with labels, battery cov
828LG MyQ™ Internet Gateway:Internet enabled accessorywhich connectsto the computerand allows you to monitor andcontrol garage door openersand lightin
4To avoid possible SERIOUS INJURY to fingerfrom moving garage door opener:• ALWAYS keep hand clear of sprocketwhileoperating opener.• Securelyattach s
RAYNOR®FIVE YEAR LIMITED WARRANTYLIFETIME MOTOR AND BELT LIMITED WARRANTYONE YEAR LIMITED WARRANTY FOR THEBATTERYBACK-UPRaynor®(“Seller”) warrantsto
52 Tighten the Belt2.1 By hand, thread the spring trolleynut on the threaded shaftuntil it isfinger tight againstthe trolley.Do notuse any tools.Sprin
6IMPORTANT INSTALLATION INSTRUCTIONSWARNING To reduce the risk of SEVERE INJURY or DEATH:1. READ AND FOLLOW ALL INSTALLATION WARNINGS AND INSTRUCTIONS
7To prevent possible SERIOUS INJURY orDEATH:• Header bracket MUST be RIGIDLYfastened to structural supporton headerwall or ceiling,otherwise garage do
8You can attach the header bracketeither to thewall above the garage door, or to the ceiling.Follow the instructionswhich will work best foryour parti
93.1 Align the rail with the header bracket.Insert the clevispin (H5) through theholesin the header bracketand rail.Secure with the ring fastener (H11
Commentaires sur ces manuels